
Commercial Metal Roof Coating
Steel roofs over a warehouse or shop on the same property get the full metal coating process with rust and screw work.

As a Noblesville shingle roof coating contractor, we coat aging asphalt shingle roofs on commercial buildings while the shingles still lie flat and hold their granules.

Noblesville shingle roof coating fits commercial buildings with asphalt shingles: church halls, clinics, small offices, and retail centers with shingled mansards or wings.
A coating made for shingles seals worn tabs and adds reflectance, which buys time before a full tear-off. It only works while the shingles are still flat, fastened, and holding most of their granules.
Coating suits a shingle roof at a certain stage of wear. These are the conditions we check before saying yes.
Some granule loss is normal on an aging roof. If the mat still shows coverage, a coating can seal the surface before it wears through.
Wind lifts tabs that lost their seal strip. We replace missing shingles and refasten loose ones before any coating goes down.
Most shingle roof leaks start at the flashing rather than out in the field. Step flashing, vent boots, and skylight curbs get resealed first.
Snow that melts and refreezes at the eaves pushes water under shingles. We check the eave line closely and seal the first courses.
Curled shingles or a deck that gives underfoot mean the roof is past coating. Those roofs need reshingling, and we will say so.
Granules wash into downspouts and pack them solid, which backs water up under the first shingle course. Clearing them is part of the prep.
Shingle coating covers the shingled part of a building. These four systems cover the rest of the property.

Steel roofs over a warehouse or shop on the same property get the full metal coating process with rust and screw work.
Flat roof sections behind a shingled mansard often hold water, and those areas get silicone.

Sloped steel roofs on outbuildings and canopies that drain well can take acrylic at a lower material cost.

Low-slope roofs that need insulation and a continuous seal over many leaks can take spray foam and a topcoat.
A shingle coating suits owners who want to delay a full reshingle on a roof that still has some life left.
The coating seals worn tabs and exposed mat while the shingles, underlayment, and deck stay in place, so services and office hours carry on below.
Light coating colors reflect sunlight that dark shingles absorb, keeping the space under the roof cooler in July.
The coating holds loose granules in place and slows the wear that heavy rain causes on aging shingles.
Coating at the right stage pushes a full tear-off further out and lets you plan the budget for it.
Heavy granule loss means the shingles are wearing toward bare mat. A roof walk now tells you whether coating still fits or reshingling is closer.
Four stages for every shingle coating job, with the go or no-go decision made in the first one.
We check shingle flexibility, granule coverage, nail pops, flashing, and the deck from the attic where we can. The roof either qualifies for coating or it does not.
Missing and damaged shingles are replaced, nail pops are reset, and flashing at walls, vents, and skylights is resealed or replaced.
A low-pressure wash removes dirt, moss, and loose granules without stripping the shingles. The roof dries fully before coating.
A coating made for asphalt shingles goes on at the manufacturer rate. It bonds to granules and lets the shingles breathe.
The shingles themselves decide this one. The left card describes a roof we would coat.
Some roofs sit between the two. A few curled shingles in one area can be replaced and the rest coated, and we price the roof both ways so you can compare.
Pricing starts from our published coating range of about $2.50 to $4.00 per square foot and lands inside it after inspection. Shingle replacement, flashing work, roof pitch and height, and safety setup at the eaves move the number.
Church halls, small offices, and retail buildings with shingled sections all qualify when the shingles lie flat, stay attached, and sit on a solid deck. Damaged shingles and flashing get fixed before the coating goes on.
Coating fits aging shingles that are still flat and fastened, and it adds a protective layer without a tear-off. Reshingling fits curled, brittle, or widely missing shingles, or a deck with soft spots. The inspection shows which.
Pick a product labeled for asphalt shingles, which breathes and bonds to the granules. Metal roof coatings trap moisture in shingles, so they stay off the shingled sections even when the rest of the property gets them.
Most commercial shingle roofs take a few days once repairs are done: one for washing, a full drying day, and one or two for coating, set by roof size and weather.
Use the ballpark form for a range on your roof size, or call to have the shingles and flashing checked on a roof walk.